View T51750GD065JFWAB_1977118.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 1 / 20 lcd module technical specification t-51750gd065j-fw-ab table of contents 1. overview ................................ ................................ ................................ ................................ ........................ 2 2. absolute maximum ratings ................................ ................................ ................................ ................. 3 3. electrical characteristics ................................ ................................ ................................ ...................... 3 4. interface pin connection ................................ ................................ ................................ ..................... 6 5. i nterface t iming ................................ ................................ ................................ ................................ ........ 7 6. block diaglam ................................ ................................ ................................ ................................ .......... 10 7. optical characteristics ................................ ................................ ................................ ......................... 11 8 . inverted scan capability ................................ ................................ ................................ .................... 13 9 . mechanical specifications ................................ ................................ ................................ .................. 14 10 . reliability test condition ................................ ................................ ................................ ................... 16 11 . inspection standards ................................ ................................ ................................ ........................... 17 12 . code system of production lot ................................ ................................ ................................ ... 18 13 . type number ................................ ................................ ................................ ................................ ........... 18 14 . applying precautions ................................ ................................ ................................ ........................... 18 15 . precautions relating product handling ................................ ................................ ..................... 19 1 6 . warranty ................................ ................................ ................................ ................................ ..................... 20 revision history rev. date page comment type no. oct 24 , 2003 first edition final revision ****** checked by (aci engineering div ision) approved by ( quality assurance div ision) prepared by (module coordination group)
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 2 / 20 1. overview t-51750gd065j-fw-ab is 6.5 ? color tft-lcd (thin film transistor liquid crystal display) module composed of lcd panel, driver ics, control circuit, and backlight unit. by applying 6 bit digital data, 640 480 , 260 k-color images are displayed on the 6.5 ? diagonal screen. input power voltage is 3.3 v or 5v for lcd driving. inverter for backlight is not included in this module. general specifications are summarized in the following table: item specification display area (mm) 132.5 (h) 99.4 (v) ( 6.5-inch diagonal ) number of dots 64 0 3 (h) 480 (v) pixel pitch (mm) 0.2 07 (h) 0.2 07 (v) color pixel arrangement rgb vertical stripe display mode normally white number of color 6bit, 262,144 colors contrast ratio 300 optimum viewing angle(contrast ratio) 6 o ? clock brightness ( cd/m 2 ) 400 module size (mm) 158 .0 (w) 120.36 (h) 11.55 (d) module mass (g) 190( typ) backlight unit ccfl, 2-tubes, replaceable surface treatment anti- reflection and hard-coating (over 2h) attached drawing dimensional outline ue-311848 characteristic value without any note is typical value . the lcd product described in this specification is designed and manufactured for the standard use in oa equipment and consumer products, such as computers, communication equipment, industrial robots, av equipment and so on. do not use the lcd product for the equipment that require the extreme high level of reliability, such as aerospace applications, submarine cables, nuclear power control systems and medical or other equipment for life support. optrex assumes no responsibility for any damage resulting from the use of the lcd product in disre gard of the conditions and handling precautions in this specification. if customers intend to use the lcd product for the above items or other no standard items, please contact our sales persons in advance.
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 3 / 20 2. a bsolute m aximum ratings item symbol min. max. unit power supply voltage for lcd vcc 0 5.5 v logic input voltage vi 0 7 v lamp current il 0 7.0 marms lamp frequency fl 40 80 khz operation temperature *1) t op 0 6 0 c storage temperature *1) t stg -2 5 7 0 c [note] *1) top, tstg 40 c: 90%rh max. without condensation top, tstg > 40 c: absolute humidity shall be less than the value of 90%rh at 40 c without c ondensation. 3. e lectrical c haracteristics (1) tft- lcd ambient temperature : ta = 25c item symbol min. typ. max. unit remarks 3.0 3.3 3.6 v for 3.3v system power supply voltage s for lcd note a) vcc 4.5 5.0 5.5 v for 5v system -- 240 -- ma for 3.3v system power supply current s for lcd note b) icc -- 180 -- ma for 5v system -- -- 100 mvp-p vcc=+3.3v permissive input ripple voltage vrp -- -- 100 mvp-p vcc=+5.0v logic input voltage high vih 2.4 -- 5.5 v vcc=max low vil 0 -- 0.8 v vcc=min (2) backlight ta=25c item symbol min. typ. max. unit remarks lamp voltage vl -- 320 -- v rms il=6.0marms lamp current il -- 6.0 note c) -- ma rms *1) lamp frequency f l 40 -- 8 0 khz *2) starting lamp voltage vs -- -- 520 v rms lamp life time lt 30000 -- -- h *3) , il= 6 .0ma rms, continuous operation
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 4 / 20 *1) lamp current measurement method (the current meter is inserted in low voltage line.) ctl cth ctl cth lcd module a inverter power supply a *2) lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. therefore, please adjust lamp frequency, and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference. *3) lamp life time is defined as the time either when the brightness becomes 50% of the initial value, or when the starting lamp voltage does not meet the value speci fied in this table.
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 5 / 20 [note] a ) power and signals sequence: t1 10 ms 200 ms < t6 0 < t2 5 0 ms 0 t7 0 < t 3 50 ms 0 < t 4 50 ms 500 ms < t 5 t1 t2 t3 d ata 3.0v or 4.5v 3.0 v or 4.5v 0 .3 v vcc t4 t5 t6 t7 backlight data : rgb data, dclk, hd, vd, dena 0. 3 v 0.3v vcc-dip conditions: 1) when 2.4 v vcc < 3. 0 v , td 10 ms 2) when vcc < 2.4 v vcc-dip conditions sh ould also follow the power and signals sequence . td 2.4 v 3.0 v or 4.5v vcc b ) typical current condition: 64- gray- bar-pattern 480 line mode vcc = +3.3 v, f h = 31.5 khz, f v =60hz, f clk = 25mhz vcc = +5.0 v, f h = 31.5 khz, f v =60hz, f clk = 25mhz c) for typical luminance of 400 cd/m 2
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 6 / 20 4. i nterface p in c onnection cn 1 (interface signal) used c onnector: df9b-31p-1v (hirose) corresponding connector: df9b-31s - 1v (hirose) pin no. symbol function 1 gnd 2 dclk ?@ clock signal for sampling catch data signal 3 hd horizontal sync signal 4 vd ?@ vertical sync signal 5 gnd 6 r0 red data signal(lsb) 7 r1 red data signal 8 r2 red data signal 9 r3 red data signal 10 r4 red data signal 11 r5 red data signal(msb) 12 gnd 13 g0 green data signal (lsb) 14 g1 green data signal 15 g2 green data signal 16 g3 green data signal 17 g4 green data signal 18 g5 green data signal(msb) 19 gnd 20 b0 blue data signal (lsb) 21 b1 blue data signal 22 b2 blue data signal 23 b3 blue data signal 24 b4 blue data signal 25 b5 blue data signal(msb) 26 gnd 27 dena data enable signal(to settle the viewing area) 28 vcc power supply (dc 3.3v or 5v) 29 vcc power supply (dc 3.3v or 5v) 30 test this pin should be open. test signal output for only internal test use. 31 rev reverse scan control. l = normal, h = reverse *) the shielding case is connected with gnd cn 2, cn 3 (backlight) backlight-side connector: bhr- 02(8.0)vs-1n(jst) inverter-side connector: sm02(8.0)b-bhs(jst) pin no. symbol function 1 cth vblh ?i high voltage ?j 3 ctl vbll ?i low voltage ?j ?@?@?@?@?@ [note] vblh-vbll = vl
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 7 / 20 5. i nterface t iming (1) timing specifications item symbol min. typ. max. unit frequency f clk 20 25 30 mhz period t clk 33.3 40 50 ns low width t wcl 10 -- -- ns dclk high width t wc h 10 -- -- ns set up time t ds 5 -- -- ns d ata (r,g,b,dena, hd, vd) hold time t dh 5 -- -- ns horizontal active time t ha 640 640 640 t clk horizontal front porch t hfp 0 -- -- t clk horizontal back porch t hbp 7 -- -- t clk vertical active time t v a 480 480 480 t h vertical front porch t vfp 1 20 -- t h dena vertical back porch t vbp 8 20 -- t h frequency f h 27 31.5 38 khz period t h 26.3 31.7 37.0 m s hd low width t whl 5 -- -- t clk frequency f v 55 60 70 hz period t v 14.3 16.7 18.2 ms vd low width t wvl 3 -- -- t h [note] 1) data is latched at fall edge of d clk in this timing specification. 2) polarities of hd and vd are negative in this specification. 3) dena (data enable) should always be positive polarity as shown in the timing specification. 4) d clk should appear during all invalid period, and hd should appear during invalid period of frame cycle. 5) accepted only 640 data and 480 lines. 6) both hrev and vrev should be stable during operation.
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 8 / 20 (2) timing chart ( 3 ) color data assignment a. pixel timing chart 0.7 v cc 0.3 v cc t wch t wcl t clk t d ?r t d ?g dclk data(r ,g,b), dena, hd, vd 0.3v cc 0.7v cc dclk data (r ,g,b) 1 2 639 640 3 invalid data invalid data t ha t hfp t hbp t whl t h =1/f h first data last data dena hd b. horizontal timing chart c. vertical timing chart 1 2 479 480 3 invalid data invalid data t wvl t vfp t vbp t v =1/f v line data vd dena hd t va
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 9 / 20 r data g data b data color input r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 data ms b lsb ms b lsb ms b lsb black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 basic blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 color cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 red (2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (1) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 green (2) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 green green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 blue (2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 blue blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 [note] 1) definition of gray scale color (n) --- n indicates gray scale leve l. higher n means brighter level. 2) data 1:high, 0: low
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 10 / 20 6. b lock diaglam i/f connector timing converter driver(source) tft-lcd driver(gate) power supply circuit backlight ccfl 1 3 cn 2, 3 g1 g2 g480 timing signal display data s1 s2 s1919 s1920 power cn1
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 11 / 20 7. o ptical c haracteristics ta=25c , vcc=3.3v, input signals: typ. values shown in section 5 item symbol condition min. typ. max. unit remarks contrast ratio cr best viewing -- 300 -- -- *1) *3) luminance lw q = f = 0 -- 400 -- cd/m 2 *2) *3) response time tr q = f = 0 -- 15 -- ms *3) *4) tf q = f = 0 -- 16 -- ms *3) * 4 ) viewing horizontal f cr 3 10 -- - 55 ~ 55 -- *3) angle vertical q -- - 60 ~ 30 -- *3) image sticking tis 2 h -- -- 2 s *5) red rx -- 0.55 -- ry -- 0.34 -- color green gx -- 0.31 -- coordinates gy q = f = 0 -- 0.56 -- -- *3) blue bx -- 0.15 -- by -- 0.17 -- white wx -- 0.31 -- wy -- 0.36 -- [note] these items are measured using bm-5a (topcon) or lcd-7000 ( otsuka electronic) under the dark room condition (no ambient light) . condition: il = 6 .0 ma rms, fl=58khz * 1) definition of contrast ratio cr=on (white) luminance / off (black) luminance: average of 5 points * 2) definition of luminance l w = on (white) luminance: average of 5 points (1,1) 160 320 480 120 24 0 360 ( 640 , 480 ) 2 4 5 3 1 measurement point
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 12 / 20 * 3) definition of viewing angle( q , f ) * 4) definition of response time w h i t e 9 0 % 9 0 % 1 0 % 1 0 % b l a c k t f t r l u m i n a n c e * 5) image s ticking continuously display the test pattern shown in the figure below for two-hours. then display a completely white screen. the previous image shall not persist more than two seconds at 25c. test pattern for image sticking test black lines white area cols 318 - 322 rows 238 - 242
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 13 / 20 8 . i nverted s can c apability this module has the capability of inverting scan direction by signaling from controller. both horizontal and vertical scan direction can be selected independently. note that scan direction cannot be changed during operation. the following figure shows the relation between the display position and the scan direction. display position normal scan: rev = ? l ? d( 1, 1) d( 2, 1) --- d( x, 1) --- d( 639 , 1) d( 640 , 1) d( 1, 2) d( 2, 2) --- d( x, 2) --- d( 639 , 2) d( 640 , 2) | | + + + | | d( 1, y) d( 2, y) --- d( x, y) --- d( 639 , y) d(640, y) | | + + + | | d( 1, 479 ) d( 2, 479 ) --- d( x, 479 ) --- d(639, 479 ) d( 640 , 479 ) d( 1,480) d( 2,480) --- d( x,480) --- d(639, 480 ) d(640, 480 ) reverse scan: rev = ? h ? d( 640 , 480 ) d(639, 480 ) --- d( x,480) --- d( 2,480) d( 1,480) d( 640 , 479 ) d(639, 479 ) --- d( x, 479 ) --- d( 2, 479 ) d( 1, 479 ) | | + + + | | d(640, y) d( 639 , y) --- d( x, y) --- d( 2, y) d( 1, y) | | + + + | | d( 640 , 2) d( 639 , 2) --- d( x, 2) --- d( 2, 2) d( 1, 2) d( 640 , 1) d( 639 , 1) --- d( x, 1) --- d( 2, 1) d( 1, 1) the following drawing shows the relationship between the viewing direction and the scan direction. normal scan reverse scan d(1,1) d(640,1) d(1,480) d(640,480) ?@?@?@?@?@?@ d(1,1) d(640,1) d(1,480) d(640,480)
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 14 / 20 9 . m echanical s pecifications (1) front side tolerance is 0.5mm unless noted.
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 15 / 20 (2) rear side tolerance is 0.5mm unless noted. [note] we recommend you referring to the detailed drawing for your design. please contact our company sales representative when you need the detailed drawing.
t-51750gd065j-fw-ab ( ab ) no. 2003-0198 optrex corporation page 16 / 20 10 . r eliability t est c ondition (1) temperature and humidity test item conditions high temperature storage 7 0c, 96 h low temperature storage -2 5 c, 96 h high temperature operation 6 0c, 96 h low temperature operation 0c, 96 h high temperature high humidity operation 40c, 90%rh, 96 h (2) shock & vibration item conditions shock level: 490 m/s 2 shock waveform: half sinusoidal wave, 11 ms (non-operation) number of shocks: one shock input in each direction of three mutually p erpendicular axis for a total of six shock inputs frequency : 10- 57hz / vibration width(one side):0.075mm vibration :58- 500hz / gravity : 9.8m/s 2 (non-operation) sweep time: 11minutes test period: 3hrs for each direction of x,y,z (3) judgment standard the judgment of the above tests should be made as follow: pass: normal display image with no obvious non-uniformity and no line defect. partial transformation of the module parts should be ignored. fail: no display image, obvious non-uniformity, or line defects.

▲Up To Search▲

Price & Availability of T51750GD065JFWAB

	To Download T51750GD065JFWAB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .